Arizona Well Registration: How Do You Find Your Well’s 55 Number?
Arizona well registration runs through the Arizona Department of Water Resources, or ADWR. Since 1980, ADWR has filed registered wells under numbers like 55-123456: the 55, a dash and six digits. Some older wells, permitted by the State Land Department before 1980, are filed under a 35 prefix instead.
To find your well, search ADWR’s Wells55 database by that number, or search by parcel with ADWR’s search wizard. The scanned file sits in Imaged Records, and you can download it as a PDF. The driller’s log in that file shows how the well was built, from the casing to the depth to water. Those are the numbers a well pump replacement gets sized and set to.
What Is a Well Registration Number in Arizona?
It is the number ADWR keeps your well’s file under. The Arizona Groundwater Management Act of 1980 required everyone to register their wells with the new department. A new well gets its number when its Notice of Intent is filed. Drilling a new well, or deepening or modifying one, takes that notice and a licensed well driller.
A well from before 1980 may have no Notice of Intent on file. Its file should hold a Registration of Existing Wells form, filed no later than 1985. Either way, wells are registered to the parcel where they physically sit. For a shared well, that may not be the parcel with your house.
How Do You Look Up Your Well on ADWR’s Website?
ADWR’s Well Record Search page opens with a plain question: “Looking for a well registration number?” These are the ways in.
- By registration number. If you have the number, search the Wells55 database with it.
- By parcel. ADWR suggests its search wizard to search by parcel number. Use the parcel the well sits on.
- By location. Search on the cadastral location: township, range and section. A township is 6 miles by 6 miles, with 36 sections. A section search lists every well in that square mile, so expect several files to open.
- By map. A University of Arizona Cooperative Extension guide describes a statewide map of registered wells. Each one shows as a red dot at its approximate spot.
That guide dates from 2015, so ADWR’s menus may look different today. ADWR also posts a cadastral location guide and a How to Find my Well video. However you search, the scanned file itself lives in Imaged Records, ready to download as a PDF.
What Is in a Well’s ADWR File?
The file can hold paperwork from each stage of the well. These are the forms that turn up most often.
| Form | What it is | Who files it | When |
|---|---|---|---|
| DWR 55-40, Notice of Intent | The request to drill, deepen, replace or modify a well | The person planning the work | Before the work starts |
| DWR 55-55, Well Driller Report and Well Log | The driller’s log: how the well was built and what it was drilled through | The well driller | Up to 30 days after the well is finished |
| DWR 55-56, Pump Installation Completion Report | The pump installed, its capacity and the well yield test | The well owner, not the driller | Up to 30 days after a pump goes in |
| DWR 55-71A, Request to Change Well Information | Corrections and changes to the record, including a transfer of ownership | An escrow officer at a sale, otherwise the owner | At closing, or when the well’s details change |
Which Parts of the Record Matter for Pump Work?
Start with the driller’s log. ADWR’s homeowner guide lists what the log records, including the type and size of casing and the depth to water. Add the total depth, and you have the numbers that frame any pump job.
The total depth tells how far down a pump can hang. The casing size decides how wide a pump can be. The water level is the first guide for setting the pump below the water. We have seen a new pump set above the water level that never pumped until it was reset lower.
Treat old numbers as a starting point, since water levels can change over the years. If a well now measures far shorter than its log, it may have filled in with sediment. That calls for a look at well cleaning and rehabilitation.
Then check the pump report, if the file has one. ADWR’s guide says it covers the type of pump installed, the pump capacity and the well yield test. A pump swapped years ago with no new report leaves the file out of date.
If the well has quit outright, start with the safe checks for a well with no water. If those do not find it, the next step is well pump repair, with the record on hand.
Buying a Property With a Well? Check the Registration First
UA Extension’s registry guide warns that buyers and lenders will ask for the well’s records. Pull the file before closing and match it to the well on the land. Check the owner name too. Recording a deed did not, on its own, tell ADWR that a well changed hands.
That gap left many wells listed under whoever first registered them between 1981 and 1985. Escrow officers use form 55-71A to record a transfer of well ownership with ADWR at closing. ADWR’s Constituent Portal also takes a change of well ownership online.
After closing, search the well again and check that your name is on it. Without the well in your name, UA Extension warns, you may not have a known or definable source of water.
Who Files the Pump Installation Completion Report?
The well owner does. ADWR’s homeowner guide says the owner, not the well driller, must file the Pump Installation Completion Report, form DWR 55-56. The deadline is 30 days after the well is equipped with a pump. In ADWR’s own words, “Your pump installer should be able to help you complete the report.”
The statute does not spell out pump replacements, UA Extension notes. Its authors recommend a new 55-56 each time the pump is replaced or set at a new depth. The same guide says up to date records save the owner time and costs when repairs come up.
Is Your Well an Exempt Well?
ADWR’s homeowner guide says an exempt well has a maximum pump capacity of 35 gallons per minute. Typical uses include non-irrigation purposes, noncommercial irrigation of less than two acres, and watering stock. Most exempt wells are used for residences.
UA Extension notes there are no Active Management Areas within Gila County. Outside those areas, it says, there are no pumping restrictions on domestic wells. If your well is outside Gila County, ask ADWR whether it sits in an AMA.
The 35 gallons per minute line is about pump capacity, so it can come up when a pump is replaced. Before a bigger stock or irrigation pump goes in, ask ADWR how it would affect the well.
What About Wells on Reservation Land?
The state registry covers land under state jurisdiction. UA Extension’s Gila County guide says the state of Arizona in general has no regulatory authority on tribal lands. A well on reservation land may not be in ADWR’s records, and the state forms may not apply. Ask the tribal or federal office that handles land and water where the well sits.
Ready to Put the Record to Work?
Have the registration number and the driller’s log in hand before any pump work starts. If the pump needs replacing, those numbers feed straight into sizing it. Our page on replacing a well pump covers how that job goes.
Based in Globe, we work wells across Gila County and up to about 75 miles out. Call or text (928) 961-6641 with the registration number handy, and we quote the job before work begins.